Search found 124 matches
- Fri Jul 26, 2019 1:54 pm
- Forum: Classifieds - XR4Ti
- Topic: 2 XR4Ti projects
- Replies: 1
- Views: 515
2 XR4Ti projects
Two Projects for sale with a bunch of parts. Red one runs but is ugly https://youtu.be/JmhcmJd4tMc Black one has no drivetrain installed but body is nice. https://youtu.be/Bpol2AWik1s I think it has a little dent somewhere. The existing interior of the black one sucks but I have a set of cloth seats...
Re: Shaky
yeah thanks maybe it is the inner tie rod ends
The tires had been sitting which might make it worse but I had this problem before I parked it. It’s weird like it’s worse under load like going uphill. I checked the guibo and it’s ok too.
The tires had been sitting which might make it worse but I had this problem before I parked it. It’s weird like it’s worse under load like going uphill. I checked the guibo and it’s ok too.
Re: Shaky
I fixed the links. Apparently Facebook links don’t work.
Shaky
Hey guys. It looks like you’re still here. What do you think this shaky shaky is?
https://youtu.be/o70esX4BMaM
https://youtu.be/oB6xmeDQbOc
https://youtu.be/UaSGyZyTcbU
https://youtu.be/o70esX4BMaM
https://youtu.be/oB6xmeDQbOc
https://youtu.be/UaSGyZyTcbU
Re: Gas
Thanks for the line from San Diego!
back on the road.

Re: Gas
check at the parts store. just take the line with you to compare. they have assorted sizes. Too funny! I got a couple of fittings that look a little different, some tubing to bend in boiling water, and a "good luck" from the parts guy. He also said "It's too bad they came up with dumb ideas like th...
Re: Gas
I need a new line from the fuel filter to the fuel pump. Does anyone have a merkur graveyard that wants to part with one? I could try to make one but I'm not sure about bending the nylon this looks like it's factory bent. I can get a 90 new but then there is another 90 after that on each end. The fi...
Re: Gas
It was leaking at the outlet of the high pressure pump. There is rust on the outlet. I got the inlet off ok but I had a hard time with the outlet. Finally it came off but a white plastic piece with two o rings is stuck on the pump outlet. the black potion of the connector is intact. Usually when I r...
Re: Gas
Yeah, tank was only 1/2 full so probably not the o-ring at the top
I'll let you know when I get to it... thanks.
I'll let you know when I get to it... thanks.
Gas
Humpty Dumpty is leaking gasoline somewhere in the back. To those of you who have experienced this, what did you end up replacing? Thanks.
- Thu Sep 18, 2014 6:38 am
- Forum: XR4Ti
- Topic: Humpty Dumpty
- Replies: 11
- Views: 4075
Re: Humpty Dumpty
So I have to take the valve cover off to get to the blower motor?? Only in a Merkur...
- Wed Sep 17, 2014 3:34 pm
- Forum: XR4Ti
- Topic: Humpty Dumpty
- Replies: 11
- Views: 4075
Re: Humpty Dumpty
I've tried the garden hose before. I'll see about tearing it apart to get to the motor and core
- Mon Sep 15, 2014 9:03 am
- Forum: XR4Ti
- Topic: Humpty Dumpty
- Replies: 11
- Views: 4075
Humpty Dumpty
I drove Humpty Dumpty to work today. I had been losing interest for quite some time, but just this weekend I replaced a rotor and there is much less shaking.
Now, if I could get the thing to stop blowing cold air on my feet - I need a fan motor and maybe a heater core. Any tips?
Thanks.
Now, if I could get the thing to stop blowing cold air on my feet - I need a fan motor and maybe a heater core. Any tips?
Thanks.
- Wed May 02, 2012 6:30 am
- Forum: XR4Ti
- Topic: Speedo broken, whirring sound
- Replies: 17
- Views: 3860
Re: Speedo broken, whirring sound
Anyone else get excited when there speedometer starts to randomly work again for a few minutes? haha 

- Tue Apr 10, 2012 8:04 am
- Forum: XR4Ti
- Topic: RIP Humpty Dumpty
- Replies: 34
- Views: 4361
Re: RIP Humpty Dumpty
Hmmm. I can't stop obsessing over this. Leave it all in black primer? Roll on some rustoleum? Or $500 for orange peel? Save time and money for the 86... My son Ben who is 4 is already telling me about the 86 "we have to get my car fixed ...pull it out of here and clean out the spider webs ...go to t...