Search found 860 matches

by jkxr4ti
Wed Aug 07, 2019 9:13 pm
Forum: Off-Topic Discussion
Topic: Caminofication
Replies: 4
Views: 2067


Brad, when did you start writing for Automobile magazine???? ... MAGArticle
by jkxr4ti
Mon May 27, 2019 11:14 am
Forum: XR4Ti
Topic: Saginaw Power Steering Pump Conversion
Replies: 35
Views: 6174

Re: Saginaw Power Steering Pump Conversion

So the Astro pump is key here because it uses a straight snout vs the majority of the Saginaw pumps that have the tapered version. Were there other Saginaw pumps with a attached reservoir and a straight snout? That and the horseshoe adapter bracket really make this a bolt on affair aside for the cle...
by jkxr4ti
Sun Mar 31, 2019 3:41 pm
Forum: XR4Ti
Topic: Question installing AEM wide band 30-4110...
Replies: 7
Views: 1518

Re: Question installing AEM wide band 30-4110...

If the wideband has a simulated narrowband output this can be fed to the factory ecu. The main issue with the wideband too close to the turbo is longevity. They recommend 18” down stream of the turbo to make it last. I have mine 1/2 way through the downpipe. I’ve replaced a couple sensors in the 10 ...
by jkxr4ti
Sun Mar 03, 2019 9:09 pm
Forum: XR4Ti
Replies: 13
Views: 2315


This kit from Jegs works great on our fuel rail. It spaces the gauge high enough to clear the rail. Using the side position points it toward the fender for easy viewing. Been using one of these on my car for quite a few years. If you prefer not to have the brass finish you can always paint it. https...
by jkxr4ti
Sat Sep 01, 2018 10:11 am
Forum: XR4Ti
Topic: Fuel Injector upgrade
Replies: 11
Views: 2671

Re: Fuel Injector upgrade

I would suggest you look into the newer Siemens/deka high impedance injectors. These are fast opening and will work great with the MS. They draw much less current and produce less electrical noise than the low impedance injectors. I switched to these after maxing out the stock 35lb then low impedanc...
by jkxr4ti
Thu Aug 30, 2018 8:01 pm
Forum: XR4Ti
Topic: 87-89 Brake MC Kit
Replies: 28
Views: 5505

Re: 87-89 Brake MC Kit

I may still have an extra DG master cylinder kit. Let me check and get back to you.
by jkxr4ti
Sun Aug 12, 2018 8:19 am
Forum: XR4Ti
Topic: Catch Can Question
Replies: 20
Views: 4844

Re: Catch Can Question

The T inline with the valvecover and crankcase will work. Larger lines will be better here especially if your considering an open breather. I used one of those summit ones for about 3 months before the drain valve fell out the bottom. Not the best quality. One other item to consider with the open pv...
by jkxr4ti
Sun Aug 12, 2018 8:05 am
Forum: XR4Ti
Topic: Antenna Options
Replies: 6
Views: 1928

Re: Antenna Options

I installed one of these amazon/eBay self adhesive glass mount deals about 2 years ago.
by jkxr4ti
Tue May 29, 2018 4:08 pm
Forum: Classifieds - XR4Ti
Topic: Countour SVT E1 Rims Carlisle Delivery Available
Replies: 0
Views: 737

Countour SVT E1 Rims Carlisle Delivery Available

Have a set that were on my car for a number of years. These are 7/10 condition with no curb rash but not perfect finish. Currently these have some spent 215-55-16 tires on them. Available for delivery to carlisle or pickup near Rochester NY.
Asking 400 for the set.
(1.97 MiB) Not downloaded yet
(1.95 MiB) Not downloaded yet
by jkxr4ti
Mon Apr 30, 2018 9:14 pm
Forum: XR4Ti
Topic: Electrical Issue
Replies: 1
Views: 806

Re: Electrical Issue

Sounds like it could be fuse link B. I think that might be the one you just replaced a while back. Not sure if the meter would have allowed enough current to open that link. Normally they are fused on the amp terminals at around the max current value +30%. Start by measuring continuity/ohms between ...
by jkxr4ti
Fri Apr 06, 2018 10:46 am
Forum: XR4Ti
Topic: Rear Main Seal Install
Replies: 9
Views: 2260

Re: Rear Main Seal Install

Grease and a punch or clutch install tool. Just be sure to put the rag around the punch before you give it a whack.
by jkxr4ti
Thu Apr 05, 2018 5:38 pm
Forum: Carlisle 2018
Topic: Radisson Hotel Reservation Info
Replies: 20
Views: 8021

Re: Radisson Hotel Reservation Info

I have been procrastinating a bit on the planning this year. I just called and booked my room. The lady I spoke with said that the block of MCA rooms was sold out but she had no issue extending the rate and giving me a room with 2 beds. So its definitely worth calling and speaking to a live person t...
by jkxr4ti
Sat Jan 13, 2018 4:10 pm
Forum: XR4Ti
Topic: Clutches
Replies: 5
Views: 1667

Re: Clutches

Take a look at stinger performance. They have some good kits that go up to 400 ish torque.;u=00003314 I bought mine from pyropete125 over on turboford. It's comparable to the sta...
by jkxr4ti
Mon Dec 11, 2017 10:20 pm
Forum: XR4Ti
Topic: Source for brake booster grommet?
Replies: 3
Views: 1124

Re: Source for brake booster grommet?

Good find! Were you getting a vacuum leak around that grommet or noticing some wierd brake behavior?
by jkxr4ti
Sat Dec 02, 2017 10:45 am
Forum: General Discussion & Intro Forum
Topic: Greetings - New Member here
Replies: 25
Views: 5570

Re: Greetings - New Member here

Welcome aboard! Just read some of the previous posts. I was running the 215/50/16 tires on countour SVT rims and spacers. They did fit and performance was much improved. The issue now is little to no choice in tires in this size. These were only offered I believe on 2 cars factory; the PT cruiser an...