Search found 298 matches

by smoke3006
Mon Aug 25, 2008 7:39 am
Forum: Project, Photo & Video Phorum
Topic: my folvo runs
Replies: 5
Views: 1331

:cheers
by smoke3006
Thu Aug 21, 2008 7:47 am
Forum: General Discussion & Intro Forum
Topic: New pic's of my 89 XR
Replies: 18
Views: 2859

WOW!!
That is one nice looking car.
It's so freaking CLEAN!!
by smoke3006
Tue Aug 12, 2008 1:35 pm
Forum: Regional - Northeast
Topic: 5th Annual LMMC-CT All Ford Car Show! Connecticut (September
Replies: 7
Views: 2670

Sounds like fun!
Hope to be there.
by smoke3006
Tue Jul 08, 2008 8:00 am
Forum: XR4Ti
Topic: ZF Rack & Pinion?
Replies: 9
Views: 1054

hEaT wrote:Cool, I got the 2.75 turn rack.
Don't let Ray know, you might end up with his 3.5 rack when your not looking.
by smoke3006
Mon Jun 16, 2008 6:06 pm
Forum: XR4Ti
Topic: gas gauge/walbro
Replies: 7
Views: 853

Holy crap I thought Shigma had finally returned to XRs... then I looked at the date.
by smoke3006
Thu May 29, 2008 6:21 am
Forum: Project, Photo & Video Phorum
Topic: a couple of nice spring photos of the XR
Replies: 16
Views: 2739

Did you use anything special to clean the cladding?
by smoke3006
Wed May 28, 2008 2:04 pm
Forum: XR4Ti
Topic: Ream bump stop question
Replies: 2
Views: 473

Re: Ream bump stop question

Tumbler wrote:Can I trim the tabs off that are used to hold the first coil of my rear sprin in with no consequences?
Yes.
by smoke3006
Wed May 28, 2008 1:25 pm
Forum: General Discussion & Intro Forum
Topic: GTA IV, turboford looking cars
Replies: 10
Views: 1562

Re: GTA IV, turboford looking cars

If anyone has played GTA IV yet, there is a couple 80's modeled cars including 3rd gen camaro's and firebirds. The most important though. There is a car that looks JUST LIKE a Mustang SVO, but it has a Cosworth RS wing on the back and the hood vents. Basically its a SVO RS ;) they even put the rear...
by smoke3006
Wed May 28, 2008 1:22 pm
Forum: General Discussion & Intro Forum
Topic: Wonder how hard it would be to stuff one of these in an XR?
Replies: 13
Views: 3025

Cool, but why is it worth $20k? :roll: it's a champ race car engine. it's not a street car engine. it probably cost $50k new. hell even a new cossie yb will set you back more than $10k.race quality engines ain't cheap my friend, that's why race teams have sponsors. I believe Joe was more wondering ...
by smoke3006
Wed May 28, 2008 1:15 pm
Forum: XR4Ti
Topic: Rear spring install
Replies: 2
Views: 428

Up.
The piece the bottom seats in is formed for the non-flat side.
I had mine upside-down when I first installed them :oops:
by smoke3006
Wed May 28, 2008 12:59 pm
Forum: Project, Photo & Video Phorum
Topic: show us your engine bays
Replies: 122
Views: 42481

Image
Image
by smoke3006
Fri May 16, 2008 11:12 am
Forum: Project, Photo & Video Phorum
Topic: show us your engine bays
Replies: 122
Views: 42481

pyropete125 wrote:Image
Looking good so far!!

How much did you end up moving the engine back?
by smoke3006
Mon May 12, 2008 2:02 pm
Forum: XR4Ti
Topic: PE Computer Questions
Replies: 53
Views: 5894

Re: PE Computer.

On to the XR PF EEC IV. Pin 30 is connected to A/T equipped XR's ONLY. Alan Slocum recommends connecting PIN 30 and PIN 46 for installing the PE EEC IV in the XR. PIN 30 and PIN 46 ARE connected in the XR wiring harness. John Since my XR was an autotragic, I need to connect 30 to 46? The second sec...
by smoke3006
Mon May 12, 2008 7:35 am
Forum: XR4Ti
Topic: PE Computer Questions
Replies: 53
Views: 5894

Man this thread is making me more and more confused. :beats head
by smoke3006
Mon May 12, 2008 7:31 am
Forum: General Discussion & Intro Forum
Topic: New here... old Merk owner
Replies: 4
Views: 796

Welcome!