"Ray's AKA demonfire's XR4Ti build up"
Re: "Ray's AKA demonfire's XR4Ti build up"
13 Days to first points event, and of course, i decided at the last minute to change some things.
Off season changes - front spring rate changed from 500 lb / in to 600 lb / in - 1" shorter springs, also lowered height on perch slightly so about 1.5" lower static. Will adjust as needed. Lowered rear 3/4" as well.
Oil pump, erm, well, safety wired in.
Welded reinforcement tabs for front tow hooks.
Fixed some slow leaks. Still need to get that radiator fixed, but the weep is so small it doesn't phase me.
Biggest change isn't in yet, decided to go with a 238 code t5 (thanks Brad). I think the ratios with the 3.36 rear end will be good for my power levels and types of courses we have. Dropped the input shaft off to be machined today. Going to modify the input shaft to basically be a 2.3 shaft. Gave the guy all the specs. Didn't want to deal with spacer or anything.
OD on pilot bearing was 17.42mm or 0.686"
OD will be 15.00mm or 0.588"
Will reduce length on the pilot bearing by 0.250" and also push back the spline portion 0.250".
Disassembled and inspected the gears - everything looked really nice, not worn, blocker plates, synchros, etc didn't appear to be worn. Not much, if any metal on the magnet so i'm hopeful.
Really didn't do much else, car was pretty sorted last year.
Have some pics on my phone. Nothing really exciting.
I might weld a cover on instead of that polycarbonate plate on the intake manifold. Not entirely sure yet.
Off season changes - front spring rate changed from 500 lb / in to 600 lb / in - 1" shorter springs, also lowered height on perch slightly so about 1.5" lower static. Will adjust as needed. Lowered rear 3/4" as well.
Oil pump, erm, well, safety wired in.
Welded reinforcement tabs for front tow hooks.
Fixed some slow leaks. Still need to get that radiator fixed, but the weep is so small it doesn't phase me.
Biggest change isn't in yet, decided to go with a 238 code t5 (thanks Brad). I think the ratios with the 3.36 rear end will be good for my power levels and types of courses we have. Dropped the input shaft off to be machined today. Going to modify the input shaft to basically be a 2.3 shaft. Gave the guy all the specs. Didn't want to deal with spacer or anything.
OD on pilot bearing was 17.42mm or 0.686"
OD will be 15.00mm or 0.588"
Will reduce length on the pilot bearing by 0.250" and also push back the spline portion 0.250".
Disassembled and inspected the gears - everything looked really nice, not worn, blocker plates, synchros, etc didn't appear to be worn. Not much, if any metal on the magnet so i'm hopeful.
Really didn't do much else, car was pretty sorted last year.
Have some pics on my phone. Nothing really exciting.
I might weld a cover on instead of that polycarbonate plate on the intake manifold. Not entirely sure yet.
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
Re: "Ray's AKA demonfire's XR4Ti build up"
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
-
- Level 5
- Posts: 521
- Joined: Thu Apr 26, 2012 8:04 am
- Location: Richmond, VA
Re: "Ray's AKA demonfire's XR4Ti build up"
Nice work Ray. Love the photo.
-Paul
'85 Merkur XR4Ti
K20, VW mk2
'89 K2500, 6.0 swap
'00 Honda Insight
'85 Merkur XR4Ti
K20, VW mk2
'89 K2500, 6.0 swap
'00 Honda Insight
Re: "Ray's AKA demonfire's XR4Ti build up"
Thanks
Quick question for those of you who have had the input shaft machined from a v8 or v6 mustang t5 - is it case hardened? Mine is getting done today, just had to verify.
My class this year got pretty impressive. CP is mostly a v8 class, so i'm against a bunch of very well prepared mustangs and camaros. Some in the 600hp range. Should be fun. I'm the only 4 cyl in class... But i have been the only 4 cyl in class for years anyway.
Quick question for those of you who have had the input shaft machined from a v8 or v6 mustang t5 - is it case hardened? Mine is getting done today, just had to verify.
My class this year got pretty impressive. CP is mostly a v8 class, so i'm against a bunch of very well prepared mustangs and camaros. Some in the 600hp range. Should be fun. I'm the only 4 cyl in class... But i have been the only 4 cyl in class for years anyway.
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
Re: "Ray's AKA demonfire's XR4Ti build up"
Don't know if it's case hardened but that's the same thing we did with my V6 T5.
Did it a couple of years ago and it's been working just fine.
Did it a couple of years ago and it's been working just fine.
Re: "Ray's AKA demonfire's XR4Ti build up"
Fun day yesterday. Need to work on my driving, but my co-driver snagged first in a pretty competitive CP class in the merkur yesterday. Gotta love beating ALL the fire breathing v8's with a little 4 cyl that's older than almost everyone in class...
Car ran like a top. No issues.
all pics at cartct.com
Car ran like a top. No issues.
all pics at cartct.com
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
-
- Level 3
- Posts: 201
- Joined: Fri Feb 25, 2011 11:54 am
- Location: Beaufort, South Carolina
- Contact:
Re: "Ray's AKA demonfire's XR4Ti build up"
Where's the "Like" button?
red 88 XR WORKED, inside and out. BEFORE: 225 HP 304 Lb/Ft Torque; After is to come
1989 Scorpio, Eurofied.....Eurospec V-6 in her future???
1989 Scorpio, Eurofied.....Eurospec V-6 in her future???
- John Brennan
- Level 8
- Posts: 11630
- Joined: Wed Jun 18, 2003 4:19 pm
- Location: Scottsdale, AZ "Summer Is Coming"
Re: "Ray's AKA demonfire's XR4Ti build up"
Either on FB, or on MS-- where it's never worked, anyway. I "Like" the idea, though!usmcgunner27 wrote:Where's the "Like" button?
This is my car, and these are my people!
2015 Fiesta ST
2020 Edge 2.0 Ecoboost
2015 Fiesta ST
2020 Edge 2.0 Ecoboost
Re: "Ray's AKA demonfire's XR4Ti build up"
Love the spikes on the airdam!
Jeremy Kemp
RIP: the Mutt….1988 XR4Ti Chestnut Brown/Spice Leather
MC2 Coilovers and Bushings, Contour Rims and Rotors, Ported Motorsport Head, Cosworth 4x4 Intercooler, Holset HY35 Turbo, 80LB Injectors, Megasquirt2 EFI
RIP: the Mutt….1988 XR4Ti Chestnut Brown/Spice Leather
MC2 Coilovers and Bushings, Contour Rims and Rotors, Ported Motorsport Head, Cosworth 4x4 Intercooler, Holset HY35 Turbo, 80LB Injectors, Megasquirt2 EFI
-
- Level 5
- Posts: 521
- Joined: Thu Apr 26, 2012 8:04 am
- Location: Richmond, VA
Re: "Ray's AKA demonfire's XR4Ti build up"
Funny how everyone is wearing coats in the images. Must still be cool up there. Car looks mean dude!
-Paul
'85 Merkur XR4Ti
K20, VW mk2
'89 K2500, 6.0 swap
'00 Honda Insight
'85 Merkur XR4Ti
K20, VW mk2
'89 K2500, 6.0 swap
'00 Honda Insight
Re: "Ray's AKA demonfire's XR4Ti build up"
Yeah it's been colder than normal up here this spring. Hopefully warms up soon. Car ran like a top Love days like that.
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
Re: "Ray's AKA demonfire's XR4Ti build up"
I love this car, I learned a lot from this thread and "Joe's Rain cloud".
Miguel.
89 XR4Ti Monique; Waking up a real "Night/Mare-Coor".
T5, NPR IC, PIMP ECU, Walbro 255, Dual piston BOV, Manual BC, 3" exhaust, One piece Aluminum drive-shaft, mc2 LSD, Boport 1.5 cam, Ported and polish head, big valves, 80# injectors, Bob's log, (soon HY35).
89 XR4Ti Monique; Waking up a real "Night/Mare-Coor".
T5, NPR IC, PIMP ECU, Walbro 255, Dual piston BOV, Manual BC, 3" exhaust, One piece Aluminum drive-shaft, mc2 LSD, Boport 1.5 cam, Ported and polish head, big valves, 80# injectors, Bob's log, (soon HY35).
Re: "Ray's AKA demonfire's XR4Ti build up"
Ray how was the new Thompson yesterday?
Chris
1988 Mono Rosso Red Merkur XR4Ti - Sold!
1988 Mono Rosso Red Merkur XR4Ti - Sold!
Re: "Ray's AKA demonfire's XR4Ti build up"
It was okay - the lot they gave us was smaller than expected, but the pavement was nice. The course was somewhat simple, but fun. The road course looks like it's going to be a blast
Oh, my XR won in a large field again. Again, my co-driver did it. I need to get my head on straight. At least the car's fast
Oh, my XR won in a large field again. Again, my co-driver did it. I need to get my head on straight. At least the car's fast
-Ray
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
1985 Ford F150 - Tow Missile
1985 Merkur XR4Ti -#141 CP "Miss Daisy"
2005 Subaru LGT
http://www.cartct.com
Re: "Ray's AKA demonfire's XR4Ti build up"
Congratulations on the new victory.
Miguel.
89 XR4Ti Monique; Waking up a real "Night/Mare-Coor".
T5, NPR IC, PIMP ECU, Walbro 255, Dual piston BOV, Manual BC, 3" exhaust, One piece Aluminum drive-shaft, mc2 LSD, Boport 1.5 cam, Ported and polish head, big valves, 80# injectors, Bob's log, (soon HY35).
89 XR4Ti Monique; Waking up a real "Night/Mare-Coor".
T5, NPR IC, PIMP ECU, Walbro 255, Dual piston BOV, Manual BC, 3" exhaust, One piece Aluminum drive-shaft, mc2 LSD, Boport 1.5 cam, Ported and polish head, big valves, 80# injectors, Bob's log, (soon HY35).