PCV tube blocked?

XR4Ti / Sierra / Sierra Cosworth Discussions - Questions, problem resolution, general talk, technical tips and modifications.
Post Reply
User avatar
Matt01
Level 4
Level 4
Posts: 469
Joined: Fri Aug 10, 2012 11:29 pm
Location: Montreal (Canada)

PCV tube blocked?

Post by Matt01 » Sun Jun 16, 2019 8:03 pm

Hi All,

My car always leaks oil, Ive changed all the gaskets, but the oil seems to come from one place or another. I have an OEM PCV valve, but I was wondering if it ever happened to someone that the tube or passageway got blocked/restricted over the years.

Im just asking to see if its a common problem before ripping out the PCV system for inspection.

Thanks!
-Matt

Ed Lijewski
Level 8
Posts: 7137
Joined: Thu Sep 04, 2003 5:53 pm
Location: The Belly of The Beast

Re: PCV tube blocked?

Post by Ed Lijewski » Mon Jun 17, 2019 5:35 pm

Lots years ago I installed a professionally rebuilt block in one of my XRs. Over time minor oil dripping occurred,noticeable when parked as always over a sheet of cardboard. During oil and filter changes I noticed wetness at the oil cooler seal and oil filter adapter to oil cooler seal. Synthetic blend oil dripped more than conventional as one would expect. Coupla years ago I ordered the correct gaskets and bolt o-ring for those pieces. Last Saturday I finally installed them. Made an immediate noticeable difference (time will tell if the change is sustained).

Another common source of oil dripping is a bad oil pressure switch. I had noticed mine was wet with oil film and installed new switch some time ago; no oil film or dripping from that area now.

YMMV
Last edited by Ed Lijewski on Wed Jun 19, 2019 12:39 pm, edited 1 time in total.
Descartes: "Cogito Ergo Sum"
Lijewski: "Sum Ergo Drive-O. Mucho!

User avatar
John Brennan
Level 8
Posts: 11499
Joined: Wed Jun 18, 2003 4:19 pm
Location: Scottsdale, AZ "Summer Is Coming"

Re: PCV tube blocked?

Post by John Brennan » Tue Jun 18, 2019 8:24 am

Thoroughly clean the engine, then see where the oil drips from first.
This is my car, and these are my people!
1989 XR4Ti 5-Speed
2001 BMW Z3 3.0 5-Speed
2015 Fiesta ST 6-Speed
2015 Edge 3.5 V6 Auto/Paddles

User avatar
andyofcolumbusmerkur
Level 3
Level 3
Posts: 296
Joined: Mon Jul 15, 2013 7:58 pm

Re: PCV tube blocked?

Post by andyofcolumbusmerkur » Tue Jun 18, 2019 10:06 am

Some bolts go deep enough to get to an oil passage. Coat the threads with Indian Head Shellac. Hitting the rev limiter seems to push oil out of all kinds of places also.
You can barbecue it, boil it, broil it, bake it, saute it. There's shrimp kabobs, shrimp creole, shrimp gumbo, pan fried, deep fried, stir fried, pineapple shrimp, lemon shrimp, coconut shrimp, pepper shrimp, shrimp soup, shrimp stew, shrimp salad, shrimp in potatoes, shrimp burger, shrimp sandwich....

thesameguy
Level 7
Level 7
Posts: 1983
Joined: Mon Apr 18, 2005 5:06 pm
Location: Sacramento
Contact:

Re: PCV tube blocked?

Post by thesameguy » Fri Aug 09, 2019 10:34 am

I found the PCV hoses had hardened and didn't seal well, which reduced PCV effectiveness. Replacing the hoses did help.

My current battle is the VC breather, which sucks. I cannot get a good seal on the grommet in the head, and I don't know why. It's been that way for 15 years, first with the original '86 VC/breather combo and now with a Turbocoupe VC/breather. I personally blame the crap supply of aftermarket grommets. I am going to find a threaded solution, maybe weld a bung to the VC. It's a dumb, annoying problem to have on an otherwise totally dialed in engine bay!

Post Reply